Agilent Technologies 81101A Reference Manual Download Page 107 | Manualshive

Page: 107 / 118

background image

107

Specifications

Pulse Parameter Definitions

practice, start points may shift with changes in transition time) when
transition times are varied. This is more convenient for programming and
the width display is easy to interpret.

Pulse Delay

Interval between leading edge medians of trigger output pulse and output
pulse:

The specified and displayed value is that obtained with the fastest
leading edge. Pulse delay has two components, a fixed delay from trigger
output to output signal and a variable delay with respect to the trigger
output.

Double Pulse Delay

Interval between leading edge medians of the double pulses.

Interchannel Delay (Skew)

Interval between corresponding leading edge medians of the output
signals.

Variable Delay

Fixed Delay

Trigger

Output

Output

Signal

Double Pulse Delay

«
...
105
106
107
108
109
...
»

Summary of Contents for 81101A























































































































Reviews:

No comments

Related manuals for 81101A

Explorer 1000 Pro

Brand: Jackery Pages: 40

Brand: FEESER Pages: 32

Brand: ZIPPER MASCHINEN Pages: 42

Brand: Champion Pages: 30

Brand: K&S BASIC Pages: 13

Brand: ZIPPER MASCHINEN Pages: 93

Brand: Rheem Pages: 96

Brand: FUXTEC Pages: 83

Brand: ETQ Pages: 32

Brand: Champion Pages: 43

GALE FORCE PT8500E

Brand: PENTAGON Pages: 25

Brand: SKF Pages: 4

Brand: SKF Pages: 6

Brand: New Holland Pages: 64

Panda 4800i PMS

Brand: Fischer Panda Pages: 180

Brand: Mi-T-M Pages: 94

Brand: Mi-T-M Pages: 100

Brand: Mi-T-M Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands