background image

DirectCommand

 Installation 

Raven Accu-Flow ISO Kit

 

Ag Leader Technology 

 

 

PN: 2006375 Rev. B 

February 2015 

Page 5 of 15

 

Safety 
Notices 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

CAUTION: Implement should be lowered to ground or on 
mechanical safety stops before starting work. Do not work on 
implement supported by hydraulic system only. 
 
CAUTION: Be sure to wear proper eye protection when using any 
power tools, such as when drilling any mounting holes. 
 
IMPORTANT: Check behind vehicle and implement panels for any 
hoses, wiring, controls, etc. that could be damaged when drilling 
any mounting holes. 

 

IMPORTANT: Disconnect Ag Leader Display, DirectCommand 
components and flow meter from electrical system when welding 
on equipment or jump starting unit to prevent component damage 
due to power surges or excessive current 
 
IMPORTANT: If using a non Ag Leader GPS receiver, make sure 
to install the Null Modem Cable included in the Display kit, to 
prevent damage to the Display or the GPS receiver. 
 
IMPORTANT: Use the Dielectric grease to coat the seals and 
terminals of each connector that will be exposed to weather or 
chemicals as you plug them in. 
 
NOTE: Be sure to follow the alignment keys on the plugs and the 
receptacles carefully. Do not use excessive force when mating 
connectors. 

 

IMPORTANT: Do not drill holes in tool bar mainframe. Due to high 
stress loads on toolbar, cracking may occur from drilled holes.

 

Summary of Contents for 4200140
















Reviews: