manualshive.com logo in svg

Aficio 2404WD, Operating Instructions Manual, Page: 37 / 92

Share
Download
Aficio 2404WD Operating Instructions Manual Download Page 37

When a Message Appears

31

3

Alert Messages

This section describes the machine Alert messages. 

Message

Cause

Solution

Cannot connect 

with the wireless 

card. Turn the 

main power switch 

off, then check 

the card.

IEEE 802.11b interface 
unit was not inserted 
when the machine was 
turned on.

Turn off the machine and check the in-
terface unit is inserted correctly. Then, 
turn the machine on again. If the mes-
sage appears again, call your service 
representative.

Cannot connect 

with the wireless 

card. Turn the 

main power switch 

off, then check 

the card.

IEEE 802.11b interface 
unit was pulled out after 
the machine turned on.

Turn off the machine and check the in-
terface unit is inserted correctly. Then, 
turn the machine on again. If the mes-
sage appears again, call your service 
representative.

Problems with the 

wireless card.

A wireless card that the 
machine cannot use has 
been installed.

Turn off the machine and check the in-
terface unit is inserted correctly. Then, 
turn the machine on again. If the mes-
sage appears again, call your service 
representative.

Problems with the 

wireless board.

Access to the wireless 
board in which the IEEE 
802.11b interface unit is 
inserted is possible, but 
an error was detected. 

Turn off the machine and check the in-
terface unit is inserted correctly. Then, 
turn the machine on again. If the mes-
sage appears again, call your service 
representative.

Problem with Hard 

Disk.

An error has occurred in 
the hard disk drive.

Turn off the main power switch, and back 
on again. If the message appears again, 
contact your service representative.

The entered pass-

word is incor-

rect.

The password of the en-
crypted PDF file has 
been entered incorrectly.

Enter the correct password.

Error has oc-

curred.

A syntax error, etc., has 
occurred.

Check the PDF file is not corrupted.

USB has a prob-

lem.

An error has occurred in 
the USB interface.

Turn off the main power switch, and back 
on again. If the message appears again, 
contact your service representative.

Hardware Problem: 

Ethernet

An error has occurred in 
the Ethernet board.

Turn off the main power switch, and back 
on again. If the message appears again, 
contact your service representative.

Printing privi-

leges have not 

been set for this 

document.

You tried to print a print-
protected document.

You cannot print this document.

Summary of Contents for 2404WD





























































































Reviews:

No comments