Aeta Audio Systems ScoopTeam User Manual Download Page 77

Page: 77 / 82

ScoopTeam - User manual - Draft 0002

5.3. Network protocols and ports

TBC

The ScoopTeam implements or complies with the following protocols (non exhaustive list):



Physical and link layers: Ethernet, 100BaseT, 10BaseT



Network/Transport layers (IPv4): TCP/IP, UDP/IP, RTP/IP



Application: HTTP, Telnet, DHCP, STUN, NTP, SYSLOG



Audio transmission: SIP signaling, SDP, RTP, RTCP, RFC3550/3551, RFC3640



Compliant with EBU recommendation Tech 3326 (interoperability of audio codecs for
contribution)

The ports used by the device are the following:

Type

Port

Designation

Dir

Notes

TCP

80 HTTP



Embedded html server

7001 Control



Remote control;
used by ScoopManager

123 NTP



For querying an NTP server

UDP

514 SYSLOG



For sending messages to a SYSLOG server

2382 AETA enumeration



Used by “AetaScan”

3478 STUN



For querying a STUN server

5004

RTP



For audio streaming, SIP operation mode

5005

RTCP



For audio streaming, SIP operation mode

5060

SIP



SIP signalling

9000

RTP



For audio streaming in “Direct RTP” mode

9001

RTCP



For audio streaming in “Direct RTP” mode

Ports shown in

bold

can be changed from the default values shown in the table.

1 AetaScan is a tool that scans a network to identify AETA codecs and e.g. detect their IP addresses.

Summary of Contents for ScoopTeam



















































































Search results

Summary of Contents for ScoopTeam

Reviews:

Related manuals for ScoopTeam

Brands by name

Popular brands

Aeta Audio Systems ScoopTeam, User Manual

Search results

Summary of Contents for ScoopTeam

Reviews:

Related manuals for ScoopTeam

Brands by name

Popular brands