Aeta Audio Systems ScoopTeam User Manual Download Page 75 | Manualshive

Page: 75 / 82

background image

ScoopTeam - User manual - Draft 0002

73

5.1.11. DC power supply

The unit features a 4 pin male XLR socket for connecting a 12 V DC supply (non isolated). The unit
includes overvoltage and overcurrent protection (resettable fuse on the DC input).

The DC supply also charges the batteries inside the unit [1].

Characteristics

Min

Nominal

Max

Notes

Supply voltage

8 V

12 V

18 V

[1]

Supply current

TBD

A

2 A

[2]

[1]:

TBC

.

[2]: The power consumption may vary in a wide range depending on the input voltage, the installed
options, and the operating mode.
Connections on the XLR socket: Ground is connected on pin 1, and pin 4 must provide the +12 V voltage.

«
...
73
74
75
76
77
...
»

Summary of Contents for ScoopTeam



















































































Reviews:

No comments

Related manuals for ScoopTeam

Brand: Aeta Audio Systems Pages: 24

Medialon MAS Pro Dante D

Brand: 7th Sense Pages: 2

Brand: Magnavox Pages: 24

Brand: GRS Pages: 4

Brand: BriarTek Pages: 2

Brand: Crestron Pages: 26

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 33

Brand: Panasonic Pages: 15

TraxOil OM3-020P

Brand: Emerson Pages: 3

Brand: Emerson Pages: 15

White Rodgers 50A65-5165

Brand: Emerson Pages: 8

Brand: Emerson Pages: 14

Brand: Emerson Pages: 47

Liebert Challenger iCOM 3000

Brand: Emerson Pages: 48

PACSystems RSTi-EP

Brand: Emerson Pages: 539

TeamWork Connect 300 Kit

Brand: Extron electronics Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands