background image

 

FINISHING AND 
PREFLIGHT 
REPARATION  

 

Center of Gravity     

 

1.  The recommended CG is 3 7/8” inches from the 

leading edge of the wing at the wing root where it 
meets the fuse.  

Do not skip this step!   

 

 
 
 

 

 

2. 

Balance the Stingray with the battery installed 
and ready to fly.  The motor, speed control, 
servos, and battery you use will determine the 
final weight and locations of equipment.  Try to 
balance the model by moving the battery, speed 
control, and receiver before adding any ballast.

 

 

 

 
 
 

 
 
 
 
 
 
 
3. Start at recommended CG until you are 

comfortable with the flight characteristics of the 
aircraft.  You may find this a bit nose heavy at 
first but that is fine to start with.  After you are 
comfortable adjust the CG to suit your flying 
style in small steps, especially when shifting the 
CG toward the tail.  Move the battery or add 
small stick on weights to the nose or tail as 
necessary.   

 
4.  For aerobatic flying a more aft balance point is 

better.  For smooth sport flying a more forward 
CG is better.  An aircraft that is too nose heavy 
does not fly well and is difficult to land.  A tail 
heavy aircraft is uncontrollable and will likely 
crash.  

 

Control Throws    

 
5.  The amount of control throw should be adjusted 

using mechanical means as much as possible and 
then electronically with the radio.  The control 
throws are shown in degrees and inches of 
deflection measured at the widest point of the 
control surface for both low and high rates. 

 
6.  Aileron throw measured in inches. 
 

 

 

38 

 

Summary of Contents for STINGRAY ELECTRIC ARF










































Reviews: