![background image](http://html.mh-extra.com/html/aeroqual/aqm60/aqm60_user-manual_2862855073.webp)
Page | 73
Aeroqual AQM60 User Guide
* SENSOR_NUM - 1 byte, specify the valid numbers of sensor has been used by the AQM box, max
number is 14.
* SENSOR_1, SENSOR_2, SENSOR_3, SENSOR_4, SENSOR_5, SENSOR_6, SENSOR_7,
SENSOR_8, SENSOR_9, SENSOR_10, SENSOR_11, SENSOR_12, SENSOR_13, SENSOR_14,
SENSOR_15, SENSOR_16, SENSOR_17, SENSOR_18, SENSOR_19, SENSOR_20
- Specifies the sensor type has been used for the AQM box. The value will be any of Sensor type value.
* AQM_STATUS - 1 byte, used specify AQM auto report data and auto zero calibration, see section 2 for
details.
6. Set monitor operation settings command 4 bytes followed by 8 bytes,
RECEIVER, AQM_ID, SET_OPERATION, CHECKSUM
RECEIVER, AQM_ID, SET_OPERATION, AUTO_REPORT_RATE, ZERO_CAL_INTERVAL,
AUTO_ZERO_READ_FREQ, OPRATION_STATUS, CHECKSUM
* SET_OPERATION - 1 byte command, see section 2 for values.
* AUTO_REPORT_RATE - 1 byte, specify the auto data report rate in minutes maximum 255 minutes. It's
only valid, when AQM_STATUS bit 0 is 1.
* ZERO_CAL_INTERVAL - 1 byte, specify the auto zero calibration interval in hours maximum 255 hours.
It's only valid, when AQM_STATUS bit 1 is 1.
* AUTO_ZERO_READ_FREQ - 1 byte, specify the auto zero reading frequency in hours, max 255 hours.
It's only valid, when AQM_STATUS bit 2 is 1.
* OPERATION_STATUS - 1 byte operation status, see section 2 for details.
6A. Acknowledge reply command of set operations, 4 bytes:
MONITOR, AQM_ID, SET_OPERATION, CHECKSUM
7. Get monitor operation settings command 4 bytes:
RECEIVER, AQM_ID, GET_OPERATION, CHECKSUM
8. Reply command of get monitor operations, 8 bytes:
MONITOR, AQM_ID, GET_OPERATION, AUTO_REPORT_RATE, ZERO_CAL_INTERVAL,
AUTO_ZERO_READ_FREQ, OPRATION_STATUS, CHECKSUM
9. AQM Monitor information request command, 4 bytes:
RECEIVER, AQM_ID, AQM_INFO, CHECKSUM
Example: 0x55 0x01 0xFB 0xAF
* AQM_INFO - 1 byte AQM information request command.
10. AQM monitor information reply command, 16 bytes:
MONITOR, AQM_ID, AQM_INFO, VERSION, NAME, RTC, (STATUS,) CHECKSUM
* AQM_ID - 1 byte value, indicate the AQM ID number, which range is 1 - 255.
* AQM_INFO - 1 byte sensor information request command, see section 2 for its value.
* VERSION - 1 byte, its unsigned value divided by 10 gives the AQM box version number.
* NAME - 5 bytes, the monitor name ASCII code (AQM60/AQM10/IQM60).
* RTC - 6 bytes, the monitors Real Time Clock (each field is one byte), ss:mm:hh DD/MM/YY, the year is
since 1900+YY
** User could use this command to test communications.
11. AQM Monitor zero calibration starts command 4 bytes:
RECEIVER, AQM_ID, ZERO_CAL, CHECKSUM
Summary of Contents for AQM60
Page 1: ...Aeroqual AQM60 User Guide ...