manualshive.com logo in svg

Aeroqual AQM60, User Manual, Page: 63 / 83

Share
Download
Aeroqual AQM60 User Manual Download Page 63

 

 

Page | 63  

Aeroqual AQM60 User Guide 

 

 

Noisy Readings 

Dirty optics 

Laser is old 

Optics need cleaning 

Send to your authorised distributor or 
contact Aeroqual technical support. 

Laser needs replacing. 

Send to your authorised distributor or 
contact Aeroqual technical support. 

Negative readings 

Purge filter new and shedding 
particles 

Purge flow zero 

Purge filter dirty 

Run zero cycles until purge filter no longer 
shedding particles. 

Adjust purge flow 

Replace purge filter 

Fibre Span has changed 
significantly since installation 

Dirty Optics 

Laser is old 

Optics need cleaning 

Send to your authorised distributor or 
contact Aeroqual technical support. 

Laser needs replacing. 

Send to your authorised distributor or 
contact Aeroqual technical support. 

Readings flat 

Laser failed (check laser 
current) 

Photo-detector failed 

Laser needs replacing. 

Send to your authorised distributor or 
contact Aeroqual technical support. 

Send optical engine to Met One for 
replacement detector and calibration. 

 
 

8.3.  Diagnostics  

 
The AQM has a number of sources for diagnostic information if a problem arises. These are described 
below: 
 

Event log:

 A large number of instrument events are logged on the event log file which is located on the SD 

data card. This can be downloaded remotely (if a modem is fitted) and in many cases can be used to 
determine whether a site visit is required.  
 

Messages:

 This is located on the AQM PC software tool bar. If the AQM is connected to the computer then 

event messages will be written to the Messages window in real-time. 
 

 

Diagnostics:

 This is located in the AQM PC software. If the AQM is connected to the computer then 

individual sensor modules can be interrogated to determine if there is a problem not picked up by normal 
fault detection as well as fine tune the sensor performance. Only qualified personnel should use this menu 
as incorrect use may result in sensor malfunction. Please consult Aeroqual Technical Support to understand 
how to use this feature. 
 
 
 
 

 

 

 

Summary of Contents for AQM60




















































































Reviews:

No comments