manualshive.com logo in svg

Aeroflex Gaisler RT-SPW-ROUTER, User Manual

Share
Download
Aeroflex Gaisler RT-SPW-ROUTER User Manual Download Page 95

AEROFLEX GAISLER

95

RT-SPW-ROUTER

Copyright Aeroflex Gaisler AB

June 2012, Version 1.2

14.4

RTAX2000S/SL specific pins - CG624 package

The Actel RTAX2000S/SL FPGA device has special pins that need to be correctly connected on the
printed circuit board, as shown in table 81. Please refer to the Actel data sheet [RTAX] for details.

Table 82. RTAX2000S/SL special pins - CG624 package

Name

Pin CG624

Note

CID

GND

A18, A24, A25, A2, A8, AA10, AA16, AA18, AA21, AA5,
AB22, AB4, AC10, AC16, AC23, AC3, AD1, AD2, AD24,
AD25, AE1, AE18, AE24, AE2, AE25, AE8, B1, B2, B25, B24,
C10, C16, C23, C3, D22, D4, E10, E16, E21, E5, E8, H1, H21,
H25, K21, K23, K3, K5, L11, L12, L13, L14, L15, M11, M12,
M13, M14, M15, N11, N12, N13, N14, N15, P11, P12, P13, P14,
P15, R11, R12, R13, R14, R15, T21, T23, T3, T5, V1, V25, V5

Low supply voltage, ground

All

VCCA

AB20, F22, F4, J17, J9, K10, K11, K15, K16, L10, L16, R10,
R16, T10, T11, T15, T16, U17, U9, Y4

1.5 V supply voltage for array

All

VCCDA

A12, A14, AA13, AA15, AA20, AA7, AB13, AC11, AD11,
AD4, AE12, AE17, B15, C15, C6, D13, E13, E19, F21, G10, G5,
N21, N5, W21

3.3 V supply voltage for I/O differential amplifier and JTAG
and probe interfaces.

All

VCCIB0

A3, B3, C4, D5, J10, J11, K12

3.3 V supply voltage for I/O

All

VCCIB1

A23, B23, C22, D21, J15, J16, K14

3.3 V supply voltage for I/O

All

VCCIB2

C24, C25, D23, E22, K17, L17, M16

3.3 V supply voltage for I/O

All

VCCIB3

AA22, AB23, AC24, AC25, P16, R17, T17

3.3 V supply voltage for I/O

All

VCCIB3

AA22, AB23, AC24, AC25, P16, R17, T17

2.5 V supply voltage for I/O (TBD)

All

VCCIB4

AB21, AC22, AD23, AE23, T14, U15, U16

2.5 V supply voltage for I/O (TBD)

All

VCCIB5

AB5, AC4, AD3, AE3, T12, U10, U11

3.3 V supply voltage for I/O

All

VCCIB6

AA4, AB3, AC1, AC2, P10, R9,T9

3.3 V supply voltage for I/O

All

VCCIB7

C1, C2, D3, E4, K9, L9, M10

3.3 V supply voltage for I/O

All

VPUMP

E20

Voltage External Pump. In normal operation, using the inter-
nal charge pump, should be tied to ground.

All

TRST

E6

JTAG Test Clock. Actel recommends this pin be hardwired
to ground for flight.

All

TCK

F5

JTAG Test Clock. Actel recommends this pin be hardwired
to ground. Must not be left unconnected.

All

TDI

C5

JTAG Test Data Input. Actel recommends that this pin be
hardwired to VCCDA, or left unconnected.

All

TDO

F6

JTAG Test Data Output. Must be left unconnected.

All

TMS

D6

JTAG Test Mode Select. Actel recommends this pin be hard-
wired to VCCDA, or left unconnected.

All

PRA

F13

Test Probe. The pins’ probe capabilities are disabled to pro-
tect programmed design confidentiality. These pins must be
left unconnected.

All

PRB

A13

All

PRC

AB12

All

PRD

AE13

All

NC

AA12, AA14, E12, E14, F12, F14, H12, H14, J12, J14, U12,
U14, V12, V14, Y12, Y14

No Connection. Pins are not connected to circuitry within
the device. These pins can be driven to any voltage or can be
left floating with no effect on the operation of the device.

All

CLK*

AC12, AC13, AD12, AD13, W14, W15, W13, Y13

Global clocks. When pins are unused, Actel recommends
they are tied to known state, preferably ground.

All

HCLK*

B13, B14, C12, C13, G12, G13, G14, G15

Hardwired clocks. When pins are unused, it is recommended
that they are tied to ground.

All

Summary of Contents for RT-SPW-ROUTER





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands