www.advancedco.com
23
3 Programming
3.1 Introduction
These instructions cover the configuration and programming of the panels.
NOTE: The panel is delivered in a non-configured condition. In this mode (or if the panel is
returned to factory default settings) the panel defaults to MANUAL ONLY mode of operation.
After configuring the panel, use the Level 2 EXTINGUISH MODES menu option (or the
configured key-switch / inputs) to set the panel into the AUTO+MANUAL mode.
3.1.1 Access Levels
The panel operation is protected from inadvertent and erroneous misuse by means of four access levels. These
levels are as follows:
Level 1 Untrained user
Level 2 Authorised User
Level 3 Commissioning, Service and Maintenance
Level 4 Commissioning, Service and Maintenance
– Special Tools Required
This document covers the Level 3 functions. For details on the operation and use of the panel at Levels 1 & 2,
refer to User Manual 680-148. Full details are supplied with any special tools.
A level-3 password is required to enter the commissioning menus. For details of Passwords, refer to Section
3.3.6.
Level-3 Passwords.
If this number is lost, it is not possible to enter commission mode functions.
Refer to 5.1 for further information.
3.1.2 Front Panel Controls and Indications
Key-Switch Assembly
(Optional)
U
S
B
S
U
P
P
L
Y
P
S
U
C
o
m
m
s
P
R
O
G
R
U
N
u
P
M
O
D
E
R
E
B
O
O
T
R
e
l
a
y
-
1
F
I
R
E
R
e
l
a
y
R
e
l
a
y
-
2
F
A
U
L
T
R
e
l
a
y
R
S
4
8
5
A
U
X
S
u
p
p
l
y
Z
O
N
E
-
1
-
Z
O
N
E
-
2
-
Z
O
N
E
-
3
-
S
N
D
R
-
1
-
S
N
D
R
-
2
-
S
N
D
R
-
3
-
M
O
D
E
S
e
l
e
c
t
M
a
n
u
a
l
T
r
i
g
g
e
r
H
O
L
D
A
B
O
R
T
P
r
e
s
s
u
r
e
M
o
n
i
t
o
r
V
A
L
V
E
M
o
n
i
t
o
r
F
L
O
W
M
o
n
i
t
o
r
A
c
t
u
a
t
o
r
O
u
t
p
u
t
P
R
O
G
I
n
p
u
t
-
1
P
R
O
G
I
n
p
u
t
-
2
P
R
O
G
I
n
p
u
t
-
3
P
R
O
G
I
n
p
u
t
-
4
M
A
N
U
A
L
O
N
L
Y
A
U
T
O
+
M
A
N
U
A
L
V
A
LV
E
C
L
O
S
E
D
M
A
N
U
A
L
D
I
S
A
B
L
E
D
D
I
S
A
B
L
E
D
F
A
U
L
T
T
I
M
E
R
H
E
L
D
A
B
O
R
T
E
D
R
E
L
E
A
S
E
I
M
M
I
N
E
N
T
R
E
L
E
A
S
E
D
E
X
T
I
N
G
U
I
S
H
A
N
T
P
O
W
E
R
S
Y
S
T
E
M
F
A
U
L
T
T
E
S
T
S
O
U
N
D
E
R
D
E
L
A
Y
E
D
D
I
S
A
B
L
E
S
O
U
N
D
E
R
D
I
S
A
B
L
E
D
F
A
U
L
T
S
O
U
N
D
E
R
F
A
U
L
T
F
I
R
E
S
I
L
E
N
C
E
D
G
E
N
E
R
A
L
-
1
-
D
E
T
E
C
T
I
O
N
Z
O
N
E
S
F
I
R
E
F
A
U
L
T
/
T
E
S
T
/
D
I
S
A
B
L
E
-
2
-
-
3
-
E
S
C
M
E
N
U
W
X
Y
Z
T
U
V
P
Q
R
S
G
H
I
J
K
L
M
N
O
D
E
F
A
B
C
R
E
S
E
T
S
I
L
E
N
C
E
M
U
T
E
!
RESOUND /
SOUND
ALARMS
B
S
E
N
5
4
-
2
:
1
9
9
8
B
S
E
N
5
4
-
4
:
1
9
9
8
B
S
E
N
1
2
0
9
4
-
1
:
2
0
0
3
C
L
A
S
S
-
A
E
X
T
I
N
G
U
I
S
H
A
N
T
R
E
L
E
A
S
E
P
U
L
L
D
O
W
N
A
N
D
P
R
E
S
S
B
U
T
T
O
N
Extinguishant Status
Number Buttons
Control Buttons
General Status
LCD
Navigation Buttons
Detection Zone Status
Manual Release Button
The LCD along with the LED Indicators shows the operating status of the system. Examples of the information
presented are shown below:
