ADTRAN Express XL 1200070L1 User Manual Download Page 142

Page: 142 / 187

Appendix B: Log Messages

126

Express XL/XLT User Manual

61200.070L1-1

AutoSpid Download Started

level 4
Lucent AutoSpid download feature has started.

AutoSpid Failed

level 2
ExpertISDN has failed trying to determine the ISDN line’s SPID format. This
can occur if the telephone company is not using standard SPID formats.

AutoSpid Passed

level 4
ExpertISDN has finished and has determined the ISDN line’s SPID format.

AutoSpid Retry

level 4
ExpertISDN is attempting another SPID format.

AutoSwitch AT&T

level 4
ExpertISDN has determined that the switch protocol is AT&T 5E custom.

AutoSwitch DMS

level 4
ExpertISDN has determined that the switch protocol is Nortel DMS-100.

AutoSwitch NI-1

level 4
ExpertISDN has determined that the switch protocol is National ISDN 1.

Bad call type

level 1
Internal error as a result of outgoing call attempt.

Bad Host_Call_ID

level 1
Internal error as a result of call control.

Bad phone number

level 2
An outgoing call was attempted with a badly formatted or empty phone num-
ber.

Summary of Contents for Express XL 1200070L1




























































































































































































Search results

Summary of Contents for Express XL 1200070L1

Reviews:

Related manuals for Express XL 1200070L1

Brands by name

Popular brands

ADTRAN Express XL 1200070L1, User Manual

Search results

Summary of Contents for Express XL 1200070L1

Reviews:

Related manuals for Express XL 1200070L1

Brands by name

Popular brands