manualshive.com logo in svg

ADTRAN Express XL 1200070L1, User Manual, Page: 134 / 187

Share
Download
ADTRAN Express XL 1200070L1 User Manual Download Page 134

Appendix A: Loop Status Messages

118

Express XL/XLT User Manual

61200.070L1-1

DISCONNECTING

A call is in the process of being disconnected.

DMS-100 Ready

The ISDN link layers 1 through 3 are up against a Nortel DMS-100 switch and 
is ready for calls.

Echo: Tx: X Rx: Y

The current transmit and receive count for the PPP echo request test.

Getting TEI #1

The Express XL/XLT’s ISDN layer 1 is up and is now getting the first TEI from 
the ISDN network.

Getting TEI #2

The Express XL/XLT’s ISDN layer 1 is up and one TEI is obtained. It is now 
getting the second TEI from the ISDN network.

ISDN-1 Ready

The ISDN link layers 1 through 3 are up against a switch running the ISDN-1 
protocol and is ready for calls.

Layer 1 up

The Express XL/XLT’s ISDN layer 1 is up.

Link down

The ISDN link is not synchronized.

Link In Sync

The ISDN link is synchronized but layer 1 is not up.

NET EOC LOOPBACK

Express XL/XLT has received an ISDN EOC loopback command from the 
switch.

Register SPID #1

The Express XL/XLT’s ISDN layer 1 and 2 is up and is now registering SPID 1 
with the ISDN network.

Summary of Contents for Express XL 1200070L1




























































































































































































Reviews:

No comments