ADTRAN Express XL 1200070L1 User Manual Download Page 107 | Manualshive

Page: 107 / 187

background image

Chapter 3: Terminal Menu Operation and Structure

61200.070L1-1

Express XL/XLT User Manual

91

Call Sessions/Session1 and Call Sessions/Session2

Read security: 5
The Express XL/XLT can support up to two active connections at one time.
These two menus reflect the results of PPP negotiations, user name, time con-
nected, idle timer, and data rates for the session.

PPP Links

- Reflects LCP layers active

BCP

- Shows UP if PPP Bridge Control Protocol has negotiated

successfully

IPCP

- Shows UP if PPP IP Control Protocol has negotiated

successfully

IPXCP

- Shows UP if PPP IPX Control Protocol has negotiated

successfully

CCP

- Shows UP if PPP Compression Control Protocol has negotiated

successfully

BACP

- Shows UP if PPP Bandwidth Allocation Control Protocol has

negotiated successfully

User

- Displays the user name of the PPP peer

Number(s)

- Shows the phone number dialed if outgoing call or caller

ID if incoming call.

Connect Time

- Shows the date and time when the call last connected.

Up Time

- Displays how long the call has been connected.

Idle Timer

- Current value of the idle timer (number of seconds since

filtered packet was passed through).

Tx Pkts

- Number of packets transmitted

Rx Pkts

- Number of packets received

Tx Bytes

- Number of bytes transmitted

Rx Bytes

- Number of bytes received

Tx Rate

- Current application data transmission rate

Rx Rate

- Current application data reception rate

«
...
105
106
107
108
109
...
»

Summary of Contents for Express XL 1200070L1




























































































































































































Reviews:

No comments

Related manuals for Express XL 1200070L1

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 40

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 4

ShareCenter DNS-343

Brand: D-Link Pages: 12

AirPlus G DWL-G710

Brand: D-Link Pages: 5

MYDLINK DNR-322L

Brand: D-Link Pages: 4

mydlink DNR-312L

Brand: D-Link Pages: 8

Brand: D-Link Pages: 12

Brand: D-Link Pages: 16

Brand: D-Link Pages: 88

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

Brand: Oracle Pages: 24

Brand: Conceptronic Pages: 2

Brand: EVOC Pages: 57

LinkStation Mini

Brand: Buffalo Pages: 71

Brand: TP-Link Pages: 2

Brand: Techroutes Pages: 20

Brand: Paradyne Pages: 74

Brand: Nexxt Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands