ADTRAN Express XL 1200070L1 User Manual Download Page 145 | Manualshive

Page: 145 / 187

background image

Appendix B: Log Messages

61200.070L1-1

Express XL/XLT User Manual

129

NETWORK_CONGESTION
NETWORK_OUT_OF_ORDER
NO_CIRCUIT_AVAILABLE
NO_ROUTE
NO_ROUTE_TO_DEST
NO_USER_RESPONDING
NON_SEL_USER_CLEAR
NONEXISTENT_MSG
NORMAL_CLEARING
NUMBER_CHANGED
OUTGOING_CALL_BARRED
PRE_EMPTED
PROTOCOL_ERROR
REQ_CHANNEL_NOT_AVAIL
RESOURCE_UNAVAIL
SERVICE_NOT_AVAIL
SERVICE_OPER_VIOLATED
TEMPORARY_FAILURE
TIMER_EXPIRY
UNASSIGNED_NUMBER
USER_ALERT_NO_ANS
USER_BUSY
WRONG_MESSAGE
WRONG_MSG_FOR_STATE

Conference <number>

level 5
The Express XLT has conferenced the held call with the active call. If no caller
ID is available for the ISDN line then <number> will be blank for incoming
calls.

Conference Rej <number>

level 5
The Express XLT attempted to conference but was reject by the ISDN switch.
If no caller ID is available for the ISDN line, then <number> will be blank for
incoming calls.

Connect Timeout

level 3
An outgoing call attempt has failed because the call was not answered or it
was not routed through the ISDN network.

«
...
143
144
145
146
147
...
»

Summary of Contents for Express XL 1200070L1




























































































































































































Reviews:

No comments

Related manuals for Express XL 1200070L1

Brand: Cambium Networks Pages: 29

Brand: Rain Bird Pages: 17

Brand: National Instruments Pages: 162

Brand: Paradyne Pages: 1

Brand: Netopia Pages: 38

Brand: TP-Link Pages: 131

Brand: TP-Link Pages: 37

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Brand: LevelOne Pages: 2

FiberTwist XGS2410

Brand: Genexis Pages: 7

Internet Security Appliances

Brand: SonicWALL Pages: 293

Brand: peplink Pages: 111

TS-U100 - NAS Server - USB

Brand: TRENDnet Pages: 47

Brand: Panduit Pages: 5

Brand: Sarian Systems Pages: 9

Brand: MikroTik Pages: 25

Brand: Epson Pages: 71

Brand: Epson Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands