ADTRAN Express XL 1200070L1 User Manual Download Page 153

Page: 153 / 187

Appendix B: Log Messages

61200.070L1-1

Express XL/XLT User Manual

137

TELNETD: Clr TCBF_BUFFER flag failed

level 6
Debugging message related to Telnet client function.

TELNETD: could not obtain peer ip

level 2
Telnet server function could not get IP address of Telnet client.

TELNETD: Session failed, error

level 2
A Telnet server session has failed because of an error.

TELNETD: Set TCBF_DONTBLOCK flag failed

level 6
Debugging message related to Telnet client function.

TELNETD: SOCKET creation error

level 2
Telnet server could not be started due to TCP socket error.

TFTP: can't get to host

level 2
TFTP client could not get to host.

TFTP client: unable to open port

level 2
TFTP client function could not open a UDP port.

TFTP: error rcvd - <message>"

level 2
Received error with <message> from TFTP server.

TFTP: lost communication

level 2
Lost communication to TFTP client or server during transfer.

TFTP server: unable to open port

level 2
TFTP server function could not open a UDP port.

Summary of Contents for Express XL 1200070L1




























































































































































































Search results

Summary of Contents for Express XL 1200070L1

Reviews:

Related manuals for Express XL 1200070L1

Brands by name

Popular brands

ADTRAN Express XL 1200070L1, User Manual

Search results

Summary of Contents for Express XL 1200070L1

Reviews:

Related manuals for Express XL 1200070L1

Brands by name

Popular brands