background image

 

 

ADP Unit Heater Limited Warranty 

Term of Warranty: 

Advanced Distributor Products (ADP) warrants that products sold shall be of merchantable 

quality, free of defects in material and workmanship, under normal use and service, for a period of two (2) years 

from the date of installation, 

not

 to exceed three (3) years from the date of manufacture subject to the terms of 

ADP’s limited warranty.   

Unit Heater Extended Components:

      This  warranty  provides  extended  coverage  on  Aluminized  Heat 

Exchangers  for  ten  (10)  years  and  Stainless  Steel  Heat  Exchangers  for  fifteen  (15)  years.    The  extended 

warranty  coverage  begins  with  the  installation  date  and  represents  the  total  warranty  period  for  the  specific 

component.  ADP, at its option, will furnish a replacement heat exchanger or allow a credit (in the amount of the 

heat exchanger original selling price) toward the purchase of a new ADP unit heater.  No extended coverage 

granted for HED series heat exchangers. 

For information on this product’s warranty, including accessing 

complete

 warranty terms, registering for an 

extended warranty*, or obtaining instructions on filing a warranty claim, please go to  www.ADPwarranty.com. 

In such states or provinces where registration requirements are prohibited, failure to complete 

registration by the consumer does not diminish his or her warranty rights. 

 

EQUIPMENT INFORMATION 

Please complete information below and retain this warranty for records and future reference. 

 

Unit Model Number:__________________________________ 

Serial Number:______________________________________ 

Installing Contractor:__________________________________ 

Installation Date: ________________Phone:_______________ 

 

 

 

 

 

 

 

 

2175 West Park Place Boulevard 

Stone Mountain, Georgia  30087 

www.adpnow.com 

 

18

Summary of Contents for HED Series





















Reviews: