ADLINK Technology STC2-10WP-AL User Manual Download Page 93

Page: 93 / 121

STC2-AL/KL Series

5.4.20 Advanced > Miscellaneous > Network Stack Config

uration

5.4.21 Advanced > Trusted Computing > TPM 1.2 Configu

ration

Feature

Options

Description

Network Stack

Disabled

Enabled

Enables/Disables UEFI Network Stack

IPv4 PXE Support

Disabled

Enabled

Enables/Disables IPv4 PXE boot support. If

disabled, IPv4 PXE boot support will not be

available.

IPv6 PXE Support

Disabled

Enabled

Enables/Disables IPv6 PXE boot support. If

disabled, IPv6 PXE boot support will not be

available.

PXE boot wait time

0x00

Time in seconds to wait to press ESC key to

abort PXE boot. Use +/- or numeric keys to

set. Range: 0x00-0x05 in increments of

0x01 (0-5 sec, 1 sec increments)

Feature

Options

Description

Configuration

Info only

Security Device

Support

Disable

Enable

Enables or Disables BIOS support for

security device. OS will not show Security

Device. TCG EFI protocol and INT1A

interface will not be available.

TPM State

Disabled

Enabled

Enable/Disable Security Device. NOTE:

Your Computer will reboot during restart in

order to change State of the Device.

Pending operation

None

TPM Clear

Schedule an Operation for the Security

Device. NOTE: Your Computer will reboot

during restart in order to change State of

Security Device.

Security Device

Support*

Disable

Enable

Enables or Disables BIOS support for

security device. OS will not show Security

Device. TCG EFI protocol and INT1A

interface will not be available.

Summary of Contents for STC2-10WP-AL


























































































































Search results

Summary of Contents for STC2-10WP-AL

Reviews:

ADLINK Technology STC2-10WP-AL, User Manual, Page: 93 / 121

Search results

Summary of Contents for STC2-10WP-AL

Reviews: