manualshive.com logo in svg

ADLINK Technology STC2-10WP-AL, User Manual, Page: 103 / 121

Share
Download
ADLINK Technology STC2-10WP-AL User Manual Download Page 103

 93

STC2-AL/KL Series

5.5.8

Chipset > PCH-IO Configuration > HD Audio Con

-

figuration

5.5.9

Chipset > PCH-IO Configuration > SerialIO Config

-

uration

State After G3

S0 State

S5 State

Specify what state to go to when 

power is re-applied after a power 

failure (G3 state).

Feature

Options

Description

HD Audio Subsystem 

Configuration Settings

Info Only

HD Audio

Disabled

Enabled

Auto

Control Detection of the HD-Audio 

device.

Audio Output Selection

Speaker-out

Line out

Audio Output Selection

Feature

Options

Description

SerialIo Configuration

Info Only

I2C0 Controller*

Disabled

Enabled

Enables/Disables SerialIo Controller

I2C1 Controller*

Disabled

Enabled

Enables/Disables SerialIo Controller

I2C2 Controller

Disabled

Enabled

Enables/Disables SerialIo Controller

I2C3 Controller

Disabled

Enabled

Enables/Disables SerialIo Controller

SPI0 Controller

Disabled

Enabled

Enables/Disables SerialIo Controller

> Serial IO I2C0 Settings
> Serial IO I2C1 Settings
> Serial IO I2C2 Settings
> Serial IO I2C3 Settings

Feature

Options

Description

Summary of Contents for STC2-10WP-AL


























































































































Reviews:

No comments