manualshive.com logo in svg

ADLINK Technology STC2-10WP-AL, User Manual, Page: 109 / 121

Share
Download
ADLINK Technology STC2-10WP-AL User Manual Download Page 109

 99

STC2-AL/KL Series

6 Driver & Application Installation

After  installing  the  operating  system,  all  related  drivers  must  be

installed for the system to function properly. This section describes

the drivers needed for Windows operating systems and the proce

-

dures to install them. For other operating system support, contact

ADLINK for further information.
Visit the ADLINK web site to download drivers.

6.1 Driver Installation Order

Install drivers in the following order.

1. Fully install Microsoft Windows before installing any driv

-

ers. Most standard I/O device drivers have been 

included in Microsoft Windows. For Windows 10 IoT 

Enterprise users, Administrator privilege is required to 

install the drivers.

2. Install the chipset driver.

See “Chipset Driver Installation” on page 100.

3. Install the graphics driver.

See “Graphics Driver Installation” on page 101.

4. Install the Ethernet driver.

See “Ethernet Driver Installation” on page 102.

5. Install the Management Engine driver

See “Management Engine Driver Installation” on 

page 102.

6. Install the Serial I/O driver.

See “Serial I/O Driver Installation” on page 103.

7. DI/O Driver Installation

See “DI/O Driver Installation” on page 103.

Summary of Contents for STC2-10WP-AL


























































































































Reviews:

No comments