manualshive.com logo in svg

ADLINK Technology PXIe-9834, User Manual, Page: 42 / 65

Share
Download
ADLINK Technology PXIe-9834 User Manual Download Page 42

30

 Operations

Leading

EDGE COMPUTING

3.3.4

PXI Trigger Bus

The PXIe-9834 utilizes PXI Trigger Bus[0..7] as multi-module syn-
chronization interface. The interconnected bus provided by PXI
Trigger Bus supports easy synchronization of multiple modules. 

When configured as input, the PXIe-9834 serves as a slave mod-
ule and will wait to commence signal acquisition until receiving a
trigger from the PXI Trigger Bus. When configured as output, the
PXIe-9834 serves as a master module and can output trigger to
one of the PXI Trigger Bus. Each signal can be routed from one of
the PXI Trigger Bus[0..7] by software programming.

3.3.5

PXI Star

When PXI STAR is selected as trigger source, the PXIe-9834 can
accept a TTL-compatible digital signal as a trigger signal. The trig-
ger occurs when a rising edge or falling edge is detected at PXI
STAR. This utility can configure the trigger polarity. The minimum
pulse width requirement of this digital trigger signal is 20ns. 

3.3.6

PXIe Differential Trigger

PXIe-9834 also features a trigger source from PXIe differential
trigger pin PXIe_DSTARB. The PXIe_DSTARB is a differential
signal distributed from the PXIe system timing slot, with timing
skew between any peripheral slots less than 150ps. This low slot-
to-slot skew makes it ideal for transferring synchronization trig-
gers. The trigger occurs when a rising edge or falling edge is
detected at PXIe_DSTARB. Software can configure trigger polar-
ity. Minimum pulse width requirement of this digital trigger signal is
20ns.

Summary of Contents for PXIe-9834


































































Reviews:

No comments