ADLINK Technology CoreModule 740 Reference Manual Download Page 5

Page: 5 / 46

CoreModule 740

Reference Manual

Chapter 1

About This Manual

Purpose of this Manual

This manual is for designers of systems based on the CoreModule™ 740 single board computer (SBC). This

manual contains information that permits designers to create an embedded system based on specific design
requirements.

Information provided

in this reference manual includes:

•

Product Overview

•

Hardware Specifications

•

BIOS Setup information

•

Technical Support Contact Information

Information not provided

in this reference manual includes:

•

Detailed chip specifications

•

Internal component operation

•

Internal registers or signal operations

•

Bus or signal timing for industry standard busses and signals

•

Pinout definitions for industry standard interfaces

References

The following list of references may help you successfully complete your custom design.

Specifications

•

PC/104 Specification, Revision 2.5, November, 2003

•

PC/104-Plus Specification, Revision 2.0, November, 2003
For latest revision of the PC/104 specifications, contact the PC/104 Consortium, at:

Web site:

http://www.pc104.org

•

PCI 2.2 Compliant Specifications, Revision 2.2, December 18, 1998
For latest revision of the PCI specifications, contact the PCI Special Interest Group at:

Web site:

http://www.pcisig.com

Chip Specifications

The following integrated circuits (ICs) are used in the CoreModule 740 single board computer:

•

Intel

Corporation and the N450 processor

Web site:

http://www.intel.com/products/processor/atom/techdocs.htm

•

Intel and the ICH8-M chip, used for the I/O Hub (Southbridge)

Data sheet:

http://www.intel.com/assets/pdf/datasheet/313056.pdf

•

SMSC and the Super I/O SCH3112I-NU chip used for the Super I/O controller

Data sheet:

http://www.smsc.com/media/Downloads_Public/Data_Briefs/311xdb.pdf

Summary of Contents for CoreModule 740















































Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands

ADLINK Technology CoreModule 740, Reference Manual

Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands