ADLINK Technology CoreModule 740 Reference Manual Download Page 3

Page: 3 / 46

CoreModule 740

Reference Manual

iii

Contents

About This Manual ....................................................................................................1

Purpose of this Manual ....................................................................................................................1
References ......................................................................................................................................1

Chapter 2

Product Overview......................................................................................................3

PC/104 Architecture ........................................................................................................................3
Product Description..........................................................................................................................4

Specifications.................................................................................................................................11

Chapter 3

Hardware .................................................................................................................15

Utility 2 Interface ...........................................................................................................................23

Floppy Drive Interface...............................................................................................................23
IDE Interface.............................................................................................................................23
Utility 2 Pin Signals ...................................................................................................................23

Real Time Clock (RTC) ............................................................................................................28
Oops! Jumper (BIOS Recovery) ...............................................................................................28
Serial Console ..........................................................................................................................28

Serial Console Setup...........................................................................................................28
Hot (Serial) Cable ...............................................................................................................28

Watchdog Timer .......................................................................................................................29

Summary of Contents for CoreModule 740















































Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands

ADLINK Technology CoreModule 740, Reference Manual

Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands