ADLINK Technology CoreModule 740 Reference Manual Download Page 9

Page: 9 / 46

Chapter 2

Product Overview

CoreModule 740

Reference Manual

Module Features

•

CPU

♦

Provides 166MHz Intel Atom N450 processor core

♦

DMI (Direct Media Interface) with 1 GB/s of bandwidth in each direction

♦

Enhanced SpeedStep® technology

♦

On die 512-kB, 8-way L2 cache

•

Memory

♦

512MB standard SDRAM soldered on the board

♦

667MHz Clock Speed

•

Interface Buses

♦

PC/104 and PC/104-Plus Interfaces

♦

PC/104 bus speeds up to 8MHz (16-bit ISA Bus)

♦

PC/104-Plus bus speed at 33MHz (32-bit PCI Bus)

♦

PCI 2.2 compliant

•

Utility Interfaces (2)

♦

Provide IDE port

•

Supports two enhanced IDE devices

•

Supports single master mode

•

Supports Ultra DMA 100/66/33 in master mode

•

Supports ATAPI and DVD peripherals

•

Supports IDE native and ATA compatibility modes

♦

Provide floppy drive port

•

Supports one floppy drive

•

Supports all standard PC/AT formats: 360kB, 1.2MB, 720kB, 1.44MB, 2.88MB

♦

Provide PS/2 Keyboard and PS/2 Mouse ports

♦

Provide parallel printer port with IEEE standard 1284 protocols, and EPP, ECP outputs

♦

Provide two RS-232 serial ports with full handshaking

♦

Provide two 2.0 USB ports

•

Provides one root USB hub

•

Provides two USB ports

•

Supports USB V2.0

♦

Support external reset switch

♦

Support standard external 8

speaker interface

♦

Support HDD Activity LED

♦

Support external battery for Real Time Clock operation

Summary of Contents for CoreModule 740















































Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands

ADLINK Technology CoreModule 740, Reference Manual

Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands