ADLINK Technology CoreModule 740 Reference Manual Download Page 35

Page: 35 / 46

CoreModule 740

Reference Manual

Chapter 4

BIOS Setup

Introduction

This section assumes the user is familiar with general BIOS Setup. Refer to the appropriate PC reference

manuals for information about the on-board ROM-BIOS software interface. If ADLINK has added to or
modified the standard functions, these functions will be described.

Entering BIOS Setup (VGA Display)

To access BIOS Setup using a VGA display for the CoreModule 740:

1. Turn on the VGA monitor and the power supply to the CoreModule 740.

2. Start Setup by pressing the [Del] key when the following message appears on the boot screen.

Press DEL to run Setup

3. Follow the instructions on the right side of the screen to navigate through the selections and modify any

settings.

Entering BIOS Setup (Remote Access)

This section describes how to enable the Remote Access in VGA mode and enter the BIOS setup through a

serial terminal or PC.

1. Turn on the power supply to the CoreModule 740 and enter the BIOS Setup Utility in VGA mode.

2. Set the BIOS feature

Remote Access Configuration

to [Enable] under the

Advanced

menu.

3. Accept the default options or make your own selections for the balance of the Remote Access fields and

record your settings.

4. Ensure you select the type of remote serial terminal you will be using and record your selection.

5. Select

Save Changes and Exit

and then shut down the CoreModule 740.

6. Connect the remote serial terminal (or the PC with communications software) to the COM port you

selected and recorded earlier in the BIOS Setup Utility.

7. Turn on the remote serial terminal or PC and set it to the settings you selected in the BIOS Setup Utility.

The default settings for the CoreModule 740 are:

♦

COM1

♦

115200

♦

8 bits

♦

1 stop bit

♦

no parity

♦

no flow control

♦

[Always] for

Redirection After BIOS POST

8. Restore power to the CoreModule 740 and look for the screen prompt shown below.

Press <space bar> to update BIOS

NOTE

If the setting for

Quick Boot

is [Enabled], you may not see this prompt appear on

screen. If this happens, press the <Del> key early in the boot sequence to enter
BIOS Setup.

Summary of Contents for CoreModule 740















































Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands

ADLINK Technology CoreModule 740, Reference Manual

Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands