ADLINK Technology CoreModule 740 Reference Manual Download Page 38

Page: 38 / 46

Appendix A

Technical Support

Reference Manual

CoreModule 740

Table A-1. Technical Support Contact Information (Continued)

ADLINK Technology Inc. (Korean Liaison Office)

Address:

꫑끭겑 ꫑뚽霡 ꫑뚽鶎

1506-25

뼑鵹

B/D 2

럪

2F, Hando B/D, 1506-25, Seocho-Dong,
Seocho-Gu,Seoul, 137-070, Korea

Tel:

+82-2-2057-0565

Fax:

+82-2-2057-0563

Email: [email protected]

ADLINK Technology Singapore Pte Ltd.

Address: 84 Genting Lane #07-02A, Cityneon Design Centre,

Singapore 349584

Tel:

+65-6844-2261

Fax:

+65-6844-2263

Email: [email protected]

ADLINK Technology Singapore Pte Ltd. (Indian Liaison Office)

Address: No. 1357, "Anupama", Sri Aurobindo Marg, 9th Cross,

JP Nagar Phase I, Bangalore - 560078, India

Tel:

+91-80-65605817

Fax:

+91-80-22443548

Email: [email protected]

ADLINK Technology Shanghai

Address:

Ϟ⍋Ꮦ⌺ϰᮄऎ㢇᯹䏃 ো

(201203)

300 Fang Chun Rd., Pudong New Area, Shanghai, 201203 China

Tel:

+86-21-5132-8988

Fax:

+86-21-5132-3588

Email: [email protected]

ADLINK Technology Shenzhen

Address:

䂀⧂ゑ◦⼀◉䱠㔏⥼◦◉浧㠿◦ₒ拢㟿ⷦ㔏㦾⥼

㪚

㰋

◉

(518057)

2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7,
High-Tech Industrial Park S., Shenzhen, 518054 China

Tel:

+86-755-2643-4858

Fax:

+86-755-2664-6353

Email: [email protected]

ADLINK Technology, Inc. (German Liaison Office)

Address: Nord Carree 3, 40477 Duesseldorf, Germany
Tel:

+49-211-495-5552

Fax:

+49-211-495-5557

Email: [email protected]

ADLINK Technology, Inc. (French Liaison Office)

Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France
Tel:

+33 (0) 1 60 12 35 66

Fax:

+33 (0) 1 60 12 35 66

Email: [email protected]

ADLINK Technology Japan Corporation

Address: 151-0072

㨀℻掌䂚廆◉ヰዓ廆

1-1-2

㦬㡴䞮✌ヰዓ廆ኰወ

Asahiseimei Hatagaya Bldg. 8F
1-1-2 Hatagaya, Shibuya-ku, Tokyo 151-0072, Japan

Tel:

+81-3-4455-3722

Fax:

+81-3-5333-6040

Email: [email protected]

Summary of Contents for CoreModule 740















































Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands

ADLINK Technology CoreModule 740, Reference Manual

Search results

Summary of Contents for CoreModule 740

Reviews:

Related manuals for CoreModule 740

Brands by name

Popular brands