Adeunis RF COMFORT MQTT User Manual Download Page 24

Page: 24 / 79

User Guide | COMFORT SERENITY MQTT | NB-IoT / LTE-Cat-M1

3.2. Estimated battery life with an LTE-Cat-M1
network connection

The table below has been estimated based on a product connected to an LTE-Cat-
M1 network with PSM (Power Saving Mode) support. Please note that the product's
battery life may vary depending on the selected operator.

Activated VOC Sensor, LEDs On

Sampling Frequency

Transmission Interval

Good Network
Autonomy (years)

Poor Network
Autonomy (years)

Every 10 minutes

2.8

< 1

Every 10 minutes

Every hour
(historization)

7.5

3.5

Every hour (default
product
configuration)

7.8

3.6

Every hour

Every 6 hours
(historization)

10.9

Disabled VOC sensor, LEDs On

Sampling Frequency

Transmission Interval

Good Network
Autonomy (years)

Poor Network
Autonomy (years)

Every 10 minutes

3.3

< 1

Every 10 minutes

Every hour
(historization)

12.4

4.5

Every hour (default
product
configuration)

13.1

4.6

Every hour

Every 6 hours
(historization)

> 15

Summary of Contents for COMFORT MQTT
















































































Search results

Summary of Contents for COMFORT MQTT

Reviews:

Brands by name

Popular brands

Adeunis RF COMFORT MQTT, User Manual

Search results

Summary of Contents for COMFORT MQTT

Reviews:

Brands by name

Popular brands