manualshive.com logo in svg

Adeunis RF COMFORT MQTT, User Manual

Share
Download
Adeunis RF COMFORT MQTT User Manual Download Page 18

User Guide | COMFORT SERENITY MQTT | NB-IoT / LTE-Cat-M1

18

2.1 General characteristics

Mechanical characteristics

Dimensions

111 x 61 x 40 mm

Weight

146 g

Enclosure

IP20

Mounting system

Wall-mounted or freestanding

Electrical characteristics

Batter power

Battery type: Replaceable Double Pack-Pile
FANSO Li-SOCl2 - ER18505H-2 Nominal
voltage: 3.6 V Maximum current: 70 mA
Capacity: 8200 mAh

External power supply (not included)

Input range: 4.2 V to 6.0 V Maximum
current:6700 mA

Operating conditions

Recommended operating range

+0°C to +50°C when powered by a double
pack-pile +0°C to +40°C when powered by an
external power supply

Operating temperature range

10°C to +70°C

2.2 Connectivity

2.2.1 Compatible networks and protocols

Connectivity

SIM Card

Nano SIM 4FF Class C (1.8 V)

Cellular Standard

3GPP LTE Version 13

Cellular IoT Networks

NB-IoT, LTE-Cat-M1

Data Transfer Protocol

MQTT, LwM2M (refer to the dedicated User
Guide to use the product with LwM2M
protocol)

2. TECHNICAL SPECIFICATIONS

Summary of Contents for COMFORT MQTT
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands