ADB M 5083 User Manual Download Page 66 | Manualshive

Page: 66 / 70

background image

Addenda

User Manual - page 64

www.adblighting.com

Issue 1.1

Click Properties. This opens a new window "Local Area Connection Properties"

Select Internet Protocol (TCP/IP) and click Properties

This opens a dialogue window "Internet Protocol (TCP/IP) Properties".
Very Important: now make careful notes of the settings as they are. You may need these
later to restore the original configuration.

Step 2: select the bullet: "Use the following IP address"

Step 3:IP address: enter an IP address, for example 2.1.1.1
Subnet Mask: 255.0.0.0
Click OK to close the window "Internet Protocol (TCP/IP) Properties".
Click OK to close the window "Local Area Connection Properties".
Close the window "Network Connections".

11.2 Addendum 2: Downloading of personalities for consoles

Personalities for various lighting consoles will be made available on the ADB website.
Contact your local distributor or

[email protected]

for more information.

«
...
64
65
66
67
68
...
»

Summary of Contents for M 5083







































































Reviews:

No comments

Related manuals for M 5083

Brand: KaVo Pages: 16

Brand: Taurus Pages: 28

Brand: Kärcher Pages: 54

Brand: ABB Pages: 85

Brand: DARKSTAR TECHNOLOGIES Pages: 4

Brand: TDW Pages: 2

Brand: Taurus Pages: 25

Brand: Vancare Pages: 3

Brand: Paitec Pages: 14

Brand: Eclipse Combustion Pages: 46

Brand: Bard Pages: 2

Brand: FagronLab Pages: 16

Litmann Quality 3100

Brand: 3M Pages: 2

Brand: LAWO Pages: 459

Brand: earline Pages: 13

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands