ADB M 5083 User Manual Download Page 37

Page: 37 / 70

Operation

www.adblighting.com

User Manual - page 35
Issue 1.1

5.2 DMX Mapping – the control channel

5.2.1 Control Channel

The Control channel allows special actions such as reset, lamp on/off and partial
recalibration. To start such a special action the sequence is Fire – Choose – Arm – Fire
DMX values for the Control Channel

- Fire (DMX value 00 – 20)
- Choose (Set the value of the Control channel to the value for the required action,

duration 1 s minimum and 10 s maximum)

- Arm (DMX value 241 – 255), duration 1 s minimum and 10 s maximum
- Fire (DMX value 00 – 20) (= start the action)

Value range

Command

Explanation

00 to 20

Fire

Fires the previously selected command

21 to 25

Park

Freezes the luminarie in the present state

26 to 30

Online

Recover from park, home and Accessories insertion
mode.
Recover from accessories insertion mode will always
force a reset on gobo / iris wheels

31 to 35

Not used

36 to 40

Stealth Mode

Mode to ensure silent operation at all times (only one
wheel moves at a time)

41 to 45

Quiet Mode

Mode to ensure a more silent operation (reduced
speed)

46 to 50

Fast mode

Max speed on all functions, “ no limits “

51 to 55

Reset all

Reset of all wheels

56 to 60

Reset all Shutters

61 to 65

Reset Gobo 1

66 to 70

Gobo 2/iris

71 to 75

Reset Zoom

76 to 80

Reset Focus

81 to 85

Reset Pan

86 to 90

Reset Tilt

91 to 95

Not Used

96 to 100

Calibration lens

Calibration of Zoom, Focus

101 to 105

Calibration of Shutters

106 to 110

Calibration of Pan/Tilt

111 to 115

Calibration of Iris/Gobo

116 to 120

Not Used

121 to 125

Pan invert On

126 to 130

Pan invert Off

131 to 135

Tilt invert On

136 to 140

Tilt invert Off

141 to 145

Pan/Tilt swap On

146 to 150

Pan/Tilt swap Off

151 to 155

Display On

156 to 160

Display Off

161 to 165

Factory default setting

For future releases

166 to 170

User setting 1

For future releases

Summary of Contents for M 5083







































































Search results

Summary of Contents for M 5083

Reviews:

Related manuals for M 5083

Brands by name

Popular brands

ADB M 5083, User Manual

Search results

Summary of Contents for M 5083

Reviews:

Related manuals for M 5083

Brands by name

Popular brands