manualshive.com logo in svg

ADB M 5083, User Manual

Share
Download
ADB M 5083 User Manual Download Page 50

Web page 

User Manual - page 48 

www.adblighting.com

 

Issue 1.1

 

 
Function Description 
 

 

Display always On 

 

Time out 

Display auto off 

Invert display 

Tick box when 

WARP

 is standing; don’t tick when it’s hanging. 

Brightness level 

value between 0 and 15 

 

 

Power Up Setting 

Enable: at power up, 

WARP

 will Reset all necessary rings. 

Disable: at power up, 

WARP

 will wait for the online

17

 command  before 

Resetting the necessary rings. 

 

 

Stall detection settings 
for Pan and Tilt 

Stall function 
If the 

WARP

 is consistently being hindered by an immovable object, the 

WARP

 will go in Stall.  

Stall: 

WARP

 freezes and lamp relay goes Off. 

A Stall time is given to the Stall function before the 

WARP

 will go in Stall. 

If in Stall: “Stal” is displayed on the top box display. 
The Stall time is a value between 0 and 60 seconds. 0 seconds disables 
the Stall function. 
Recover from Stall: online function or Press Enter on the top box 

 

You can edit the parameters on the browser; Send will send these parameters to the 

WARP

. 

 

                                                 

17

 See Control channel and Web page information 

Summary of Contents for M 5083







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands