manualshive.com logo in svg

ADB M 5083, User Manual

Share
Download
ADB M 5083 User Manual Download Page 46

Web page 

User Manual - page 44 

www.adblighting.com

 

Issue 1.1

 

Status can be: 
ok:  

Function is ok 

Resetting:  

Function is resetting 

Calibrating:  

Function is calibrating 

Communication error: Hard- or software problem – Refresh the information screen. If the 

error remains: contact your local ADB dealer. 

 
 
Function Description 

 

 

 

Global Ring Speed 
Mode 

WARP

 provides 3 speed settings:  

1.  NORMAL SPEED is best for most applications. 
2.  QUIET SPEED provides less noise in applications where speed is less 

important.(Half normal speed; not applicable for Pan and Tilt) 

3.  STEALTH SPEED provides almost no noise in applications where 

speed is not important. (All parameters.) 

Note: QUIET and STEALTH are only useful during performances. They 
are not useful during plotting since the 

WARP

 would seem sluggish. The 

best way to use those settings is during programming by using the control 
channel. 
 

Pan & Tilt 

Mode 

1. Normal 
2.  Swapped: Invert Pan and Tilt 

Pan 

Reset: Reset Pan 
Mode: 

1.  Normal (use ‘Absolute values’) 
2.  Do a Pan Reset at every power up (Reset Mode) 

Tilt 

Reset: Reset Tilt 
Mode: 

1.  Normal (use ‘Absolute values’) 
2.  Do a Tilt Reset at every power up (Reset Mode) 

Front accessory slot 

Reset: Reset the Front accessory 
Mode:  

1. None 
2. Iris 
3. Gobo 

Selecting an accessory will place the rings for the 

WARP

 SLOT in the insert 

position, provided DMX Value = 0 or no DMX is present.  
Standard 

WARP

 personalities will set the rear slot to Gobo. 

Rear accessory slot 

Reset: Reset rear accessory 
 
Mode:  

1. None 
2. Iris 
3. Gobo 

Selecting an accessory will place the rings for the 

WARP

 SLOT in the insert 

position, provided DMX Value = 0 or no DMX is present.  
Standard 

WARP

 personalities will set the front slot to Iris. 

Focus 

Reset: Reset of Focus 

Zoom 

Reset: Reset of Zoom 

Shutter 

Reset all shutters 
Reset S1 : Reset and rotation of shutter 1 
Reset S2 : Reset and rotation of shutter 2 
Reset S3 : Reset and rotation of shutter 3 
Reset S4 : Reset and rotation of shutter 4 

Summary of Contents for M 5083







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands