Actron AutoScanner Plus CP9180 Manual Download Page 86

Page: 86 / 104

Troubleshooting

5 – 4 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Battery Replacement

The Scan Tool requires 9V alkaline battery to operate without vehicle
power.

✓

When the battery needs to be replaced, the low-battery icon (

)

displays.

✓

Rechargeable batteries do not last as long as alkaline types and
are not recommended.

✓

Non-rechargeable Lithium (Li) battery can be used. Though
Lithium types last longer than the alkaline types, and they are more
expensive.

1.Place Display Face Down.

• On non-abrasive surface.

2. Remove Battery Cover.

• Turning phillips screw

counterclockwise.

• Slide battery cover off.

3. Remove Battery and Properly

Discard.

4. Install New Battery.

• 9V Alkaline Battery.

5. Reinstall Battery Cover.

• Slide battery cover on.

• Install phillips screw turning it clockwise.

• Do not overtighten screw.

Summary of Contents for AutoScanner Plus CP9180








































































































Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands

Actron AutoScanner Plus CP9180, Manual

Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands