Actron AutoScanner Plus CP9180 Manual Download

Page: 46 / 104

Using The Scan Tool

3 – 20 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

3.Enter code.

•All characters must be entered

•Only one character can be

changed at a time.

•Use

LEFT

RIGHT

arrow keys to scroll to desired
character.

•Use

DOWN

arrow

keys to change selected
character.

• Press

ENTER

✓

If definition could not be found (SAE or Enhanced), the Scan Tool
displays No DTC Definition Found. See Service Manual. If the DTC is
manufacturer specific the DTC is assigned to display. Refer to the
vehicle service manual for exact definition

✓

To enter another DTC, press

BACK

✓

Press

BACK

again to return to menu

from which

Code Lookup

was selected.

P0001

Press

change selected digit

Press

select another digit

Press ENTER to view

Summary of Contents for AutoScanner Plus CP9180








































































































Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands

Actron AutoScanner Plus CP9180, Manual

Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands