Actron AutoScanner Plus CP9180 Manual Download Page 81

Page: 81 / 104

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 4 – 35

Vehicle Diagnostics

❒

SAE J1850 protocol is shown as VPWM or PWM.

❒

ISO 15765-4 protocol is shown as CAN.

✓

Since CAN vehicles use module IDs larger than 2 digits, the Scan Tool
assigns a 2 digit module ID to be used in place of the actual CAN
module ID. The module ID assigned for the CAN module ID is used
in all functions of the Scan Tool.

=====================

ID   Protocols
$10   VPWM*
$1A   VPWM*

Modules Present

ID   Protocols
$10   PWM*
$1A   PWM*

Modules Present

=====================

ID   Protocols
$01   CAN*7e9
$00   CAN*7e8

Modules Present

=====================

Summary of Contents for AutoScanner Plus CP9180








































































































Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands

Actron AutoScanner Plus CP9180, Manual

Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands