Actron AutoScanner Plus CP9180 Manual Download Page 23 | Manualshive

Page: 23 / 104

background image

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 2 – 7

Getting Started

2

Diagnostic Link Connector (DLC)

The Data Link Connector (DLC) is used with scan tool to communicate
with the vehicle’s control module.

✓

Data Link Connector
Location.

❒

Under dashboard on
driver side of vehicle.

❒

If Data Link Connector
is not located under
dashboard, a label
should be there telling location.

Data Link Connector (DLC) Pins

1 - Manufacturer Reserved
2 - J1850 Bus+
3 - Manufacturer Reserved
4 - Chassis Ground
5 - Signal Ground
6 - CAN High, J-2284
7 - K Line, ISO 9141-2 & ISO/DIS 14230-4
8 - Manufacturer Reserved
9 - Manufacturer Reserved
10 - J1850 Bus-
11 - Manufacturer Reserved
12 - Manufacturer Reserved

13 - Manufacturer Reserved
14 - CAN Low, J-2284
15 - L Line, ISO 9141-2 & ISO/DIS 14230-4
16 - Battery Power

1

9

8

16

«
...
21
22
23
24
25
...
»

Summary of Contents for AutoScanner Plus CP9180









































































































Reviews:

No comments

Related manuals for AutoScanner Plus CP9180

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 42

Workio KV-S7065C

Brand: Panasonic Pages: 40

EasyReader Daisy

Brand: Koba Vision Pages: 24

Brand: Shining 3D Pages: 138

Brand: 3nStar Pages: 2

Brand: Cannon Pages: 103

Brand: Xerox Pages: 57

Brand: Faro Pages: 68

Brand: Velocity Pages: 38

imageFORMULA P-215

Brand: Canon Pages: 55

CanoScan LiDE400

Brand: Canon Pages: 8

Brand: Ferguson Pages: 45

Brand: Bosch Pages: 56

Brand: Fujitsu Pages: 2

Fi-5110EOX2 - ScanSnap! - Document Scanner

Brand: Fujitsu Pages: 2

Brand: Fujitsu Pages: 4

Brand: Fujitsu Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands