Actron AutoScanner Plus CP9180 Manual Download Page 68

Page: 68 / 104

Vehicle Diagnostics

4 – 22 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

4 4

Depending on the

Drive Cycle Monitors

one of these 2 screens

will be present.

✓

The Scan Tool display is
continuously updated. Only the “inc”
monitors are displayed. Monitors
designated “n/a” or “ok” are not
displayed.

✓

When all Monitors are

“OK”

the

following Screen is shown.

4.Return to

Previous Menu.

Press

BACK

key.

This Drive Cycle

=====================

Catalyst Mon

inc

Htd Catalyst

inc

Evap System Mon

inc

Since DTCs Cleared

=====================

Catalyst Mon

inc

Htd Catalyst

inc

Evap System Mon

inc

This Drive Cycle

=====================

All Monitors OK

Since DTCs Cleared

=====================

All Monitors OK

Summary of Contents for AutoScanner Plus CP9180








































































































Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands

Actron AutoScanner Plus CP9180, Manual

Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands