Actron AutoScanner Plus CP9180 Manual Download Page 37

Page: 37 / 104

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 3 – 11

Using The Scan Tool

✓

The tool reports its progress on
the bottom of the display.

❒

Memory Test

may take

several minutes to complete.

❒

Memory Test

results display.

❒

If no problems were
detected, then PASS is dis-
played

❒

If RAM fails, an error
message is shown.

❒

If ROM fails, a checksum is shown.

2. Return to

System Setup

menu.

•Press

ENTER

Program Mode

The Program Mode is used for
updating the Scan Tool. Instructions
are provided with upgrades.

Tool Information

=====================

S/N: 1234567
SWID: A7B1

Press BACK to Exit

SYSTEM SETUP

=====================

Contrast Adjust
Display Test
Keypad Test
Memory Test

Tool Information

Program Mode

Summary of Contents for AutoScanner Plus CP9180








































































































Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands

Actron AutoScanner Plus CP9180, Manual

Search results

Summary of Contents for AutoScanner Plus CP9180

Reviews:

Related manuals for AutoScanner Plus CP9180

Brands by name

Popular brands