background image

www.acti.com

 
 

Hardware Manual 

               

19 

Access the Camera 

Now that the camera and the PC are both having their unique IP addresses and are under the 

same network segment, it is possible to use the Web browser of the PC to access the camera. 

 

You can use 

Microsoft Internet Explorer 

to access the camera. 

 

Functionality 

Internet Explorer 

Live Video 

Yes 

Live Video Area Resizable 

Yes 

PTZ Control 

Yes 

Capture the snapshot 

Yes 

Video  overlay  based  configuration  (Motion 

Detection regions, Privacy Mask regions) 

Yes 

All the other configurations 

Yes 

 

When using Internet Explorer browser, the ActiveX control for video stream management will 

be downloaded from the camera directly 

– the user just has to accept the use of such control 

when prompted so. No other third party utilities are required to be installed in such case. 

 

The examples in this manual are based on Internet Explorer browser in order to cover 

all functions of the camera. 

 

Assuming that the camera

’s IP address is 

192.168.0.100

, you can access it by opening the 

Web browser and typing the following address into Web browser

’s address bar: 

 

http://192.168.0.100 

 

 

 

Summary of Contents for Q970






















Reviews: