manualshive.com logo in svg

Acteon X-MIND unity, Operator'S Manual, Page: 63 / 80

Share
Download
Acteon X-MIND unity Operator'S Manual Download Page 63

Page 63 of 79

ENGLISH

Operator’s manual • X-Mind unity • VH • (15) • 09/2017 • NUN0EN010H

Heating/Cooling Curves of the Toshiba D-041 anode

FIRMWARE

RXCD board

2,20

RXHVC board

2,14

   PLEASE NOTE

Firmware versions maybe periodically updated therefore the versions indicated in the chart above may be different from the versions instal-

led on the unit.

To know the firmware versions installed in your X-MIND unity please follow the instructions in the following chapter “ADVANCED SETTINGS” 

of the “X-MIND unity Installation and Maintenance manual”.

DEVICE POWER SUPPLY and ELECTRICAL CLASSIFICATION

Supply voltage

100 V à 240 V

Supply voltage frequency

50/60 Hz

Maximum Line Current

(technique factors that constitute maximum line current condition: 65kV, 7mA, 2s)

8,5 A (@100 V)

Standby current

100 mA

Maximum Adsorbed Power

850 VA

Maximum Rated Power

900 W

Adsorbed Power

(Stand-by mode, not armed)

3 VA

Adsorbed Power 

(Armed mode – 240Vac/60Hz)

26 VA

Rated Power @ 0.1s

900 W à 70 kV/6 mA

Fuse (only Line)

T10 AH 250 V

Apparent Resistance

0.2 Ω

Summary of Contents for X-MIND unity

















































































Reviews:

No comments