manualshive.com logo in svg

Acteon X-MIND unity, Operator'S Manual, Page: 54 / 80

Share
Download
Acteon X-MIND unity Operator'S Manual Download Page 54

Page 54 of 79

Operator’s manual • X-Mind unity • VH • (15) • 09/2017 • NUN0EN010H

ENGLISH

X-RAY CALIBRATION PROCEDURE

   CAUTION

Perform this operation only if necessary or suggested by the Technical Support Service 

During this operation x-rays will be emitted! 

It is mandatory to adopt all the safety measures relevant to radioprotection.

1.  To perform an X-ray tube calibration procedure please see the instructions below: Press and hold 

 key for 5 seconds until the 

message “TUBE CALIBRATION” appears on the display

2.  Keeping a safe distance away from the x-ray beam press and hold in. the exposure key 

 . 

 

The “CAL. IN PROGRESS” message will appears on the display. Exp. Led 

 is illuminated and an intermittent acoustic sound is emit-

ted.

3.  At the end of the procedure, the acoustic sound stops and the “CAL. SUCCESS” message appears on the display.

4.  When the pause light goes out the control unit will resume back to standard functioning mode and is ready for a new exam

   PLEASE NOTE

The calibration procedure takes about 50s 

After this procedure, the PAUSE 

 led will start blinking. During this period all the functions of the equipment are inhibited. Please 

wait until the X-MIND unity completes the cooling time due to the tube calibration before resuming normal operation.

88

Summary of Contents for X-MIND unity

















































































Reviews:

No comments