background image

Version 9E1

    User’s Manual, Nimbie Chorus NBCH07

                                                                                 

 

 P

REFACE

 

 

Important Safety Notices

For your safety, basic precautions should always be followed to reduce risk of
damage, electric shock, fire, and personal injury.  This includes, but not limit
to, the following:

Read this manual carefully and follow all warnings and instructions.

Operate the unit with only the proper electrical specifications as labeled

on  the  device.    Use  only  3-wire  extension  cords  that  have  3-prong
grounding  plugs  and  3-pole  grounding  receptacles  that  accept  your
device's plug.  Make sure the device is connected to a known ground.

Do not expose this unit to direct sunlight, rain, moisture, water, flammable

material, gas, dust, dirt, smoke, pollution or abrupt humidity changes.

Place  this  device  on  a  steady  level  surface  in  an  air-conditioned

environment with sufficient ventilation.  Do not move this device while the
power is on.  Handle with care.

This  device  generates  heat  during  the  duplication  process.    Out-of-

specification  or  unstable  power  supply  may  cause  overheating,  low
productivity, increased failure rate, and damage to the device.

Use  a  reliable  power  source  with  correct  voltage  and  ample  current

supply.  Give this  device a dedicated power outlet.  Do not share the
outlet with other devices.

Please  make  it  a  habit  to  always  unplug  the  power  cord  before

troubleshooting  or  performing  maintenance.    Always  turn  the  power
switch to the Off position when connecting the power cord.

Do not attempt to disassemble this device or touch  any of the moving

parts.    Refer  servicing  to  qualified  service  personnel.    Unauthorized
disassembly or repair will void all warranty.

DISCLAIMER:

This product, software, and/or documentation are designed to assist you in
reproducing only the material in which you own the copyright or for which you
have obtained permission to copy from the copyright owner. You assume full
responsibility for the legal and responsible use of the equipment, software and
information.

Unless you own the copyright or hold permission to copy from the copyright
owner, you may be violating copyright law and may be subject to payment of
damages  and  other  remedies.  If  you  are  uncertain  about  your  rights,  you
should contact your legal counsel. 

If you are neither in possession of the copyright nor have authorization from
the owner of the copyright, unauthorized copying onto recordable media may
violate copyright law and be subject to severe penalties and other remedies. 

@ 2010, Acronova Technology, Inc.

   3

Summary of Contents for Nimbie Chorus NB15









































Reviews: