manualshive.com logo in svg

Acrel AIM-R100, Installation And Operation Manual

Share
Download
Acrel AIM-R100 Installation And Operation Manual Download Page 9

 

 

 

6 

 

5.2.2 Installation method of AID150 alarm and display instrument

 

AID150 centralized alarm and display instrument, which is suitable for embedded wall installation. 

installation diagram is shown in figure below. 

 

During the decoration, firstly, the AID150 should be embedded in the wall to be fixed and be close to the 

knockouts of the pipeline, so that the wires (two power cords and two-core shielded twisted pair) can be drawn to 

the front cover, and then fix the cover on the shell with screws. 

If the AID150 centralized alarm and display instrument is installed by opening the cabinet door, the 

installation diagram is shown in figure below. 

1.Product shape

2.Size of wall

openings

3.Insert the shell

into the wall

5.Fixed LCD board

and Shell

4.Connect to the

LCD board through

the terminal

Attention：

As our products

are constantly

updated, this

drawing is for

reference only

until it has been

confirmed by the

relevant

personnel.

Acrel

Run

Comm Error Alarm

AID150

TEST

MENU

Summary of Contents for AIM-R100

























Reviews:

No comments

Brands by name

Popular brands

Load more brands