manualshive.com logo in svg

Acrel AIM-R100, Installation And Operation Manual

Share
Download
Acrel AIM-R100 Installation And Operation Manual Download Page 13

 

 

 

10 

passes through four wires A, B, C and N. Residual current transformer output lines connected to the 

corresponding terminal of AIM-R100, connecting to 100Ω resistance to empty terminal to avoid causing false 

alarms. 

(5) terminal 15, 16 of the AIM-R100 residual current monitor and Terminals A and B of AID150 centralized 

alarm and display instrument can be connected with 2x1.5 mm

2

 shielded twisted-pair cable. When AID150 

centralized alarm and display is used to monitor multiple AIM - R100, the connection mode of the communication 

line should be hand in hand (A to A, B to B, one by one), RS485 bus between the end of the first two 

communication terminal should be matches with a resistance, recommend and appendant resistance is 120 Ω. 

5.5 Matters needing attention 

(1) The residual current monitoring products, except for the AID150 centralized alarm and display 

instrument, should be centrally installed in the isolated power cabinet or distribution cabinet. centralized alarm 

and display instrument generally select wall installation. 

(2) During installation and wiring, the wiring diagram shall be strictly followed. It is better to press and 

connect the wiring with the needle-type sleeve joint, then insert the corresponding terminals of the instrument and 

tighten the screws to avoid abnormal working of the instrument due to poor contact. 

(3) the empty loop of AIM-R100 must be connected to 100Ω resistance, avoid the break line fault alarm. 

6 

Operation and Usage 

6.1 Panel 

AIM-R100 residual current monitor panel 

 

 

6.2 LED

 

instructions 

6.2.1 AIM-R100

 

residual current monitor LED instruction 

LED states 

instruction 

“RUN” 

In normal operation, the light flashes at a frequency of about once a second 

“COMM” 

Communication status of the device. the indicator light flashes while 

communication. 

On

Comm

Fault

Alarm

Medical Residual Current Monitor

Menu/

Test/Esc

Product type

LCD screen

Indicators

Key

Acrel

AIM-M100

Acrel

AIM-M100

Acrel

AIM-M100

Acrel

AIM-M100

Acrel

AIM-M100

Acrel

Acrel

AIM-M100

Acrel

AIM-M100

Acrel

AIM-M100

Acrel

AIM-M100

Acrel

AIM-M100

Acrel

AIM-R100

Summary of Contents for AIM-R100

























Reviews:

No comments

Brands by name

Popular brands

Load more brands