38
Chapter 2
DOS Flash Utility
Perform the following steps to use the DOS Flash Utility:
1.
Press F2 during boot to enter the Setup Menu.
2.
Select
Boot Menu
to modify the boot priority order, for example, if using USB HDD to Update BIOS, move
USB HDD to position 1.
3.
Execute the
FLASH.BAT
batch file to update BIOS.
The flash process begins as shown.
4.
In flash BIOS, the message
Please do not remove AC Power Source
displays.
NOTE:
If the AC power is not connected, the following message displays.
I t e m S p e c i f i c H e l p
U s e < > o r < > t o s e l e c t
a d e v i c e , t h e n p r e s s
< F 5 > t o m o v e i t d o w n t h e
l i s t , o r < F 6 > t o m o v e
i t u p t h e l i s t . P r e s s
< E s c > t o e s c a p e t h e m e n u
F 1
E S C
H e l p
E x i t
S e l e c t I t e m
S e l e c t M e n u
C h a n g e Va l u e s
S e l e c t
S u b M e n u
E n t e r
F 9
F 1 0
S e t u p D e f a u l t
S a v e a n d E x i t
B o o t p r i o r i t y o r d e r :
1 . N e t w o r k B o o t : L E G A C Y P C I D E V I C E
2 . U S B F D D :
3 . I D E 0 : H i t a c h i H T S 5 4 5 0 5 0 B 9 A 3 0 0
4 . U S B H D D :
5 . U S B C D R O M :
6 . I D E 1 : T S S T c o r p C D D V D W T S - L 6 3 3 C
B o o t p r i o r i t y o r d e r :
1 . N e t w o r k B o o t : L E G A C Y P C I D E V I C E
2 . U S B F D D :
3 . I D E 0 : H i t a c h i H T S 5 4 5 0 5 0 B 9 A 3 0 0
4 . U S B H D D :
5 . U S B C D R O M :
6 . I D E 1 : T S S T c o r p C D D V D W T S - L 6 3 3 C
F 5 / F 6
I n s y d e H 2 0 S e t u p U t i l i t y R e v . 3 . 5
Information
Main
Boot
Exit
Security
Summary of Contents for 4740G series
