background image

16

www.acclaimlighting.com

CONFIGURING THE ARIA WIRELESS DMX RECEIVER

Each Dyna Accent Mini fixture includes an internal Aria™ wireless 
DMX receiver unit to allow it to be remotely controlled by an 
Acclaim Lighting Aria transmitter. Fifteen radio addresses (channels) 
are available to choose from, allowing you to avoid potential 
interference sources, such as WiFi access points, and set up parallel 
wireless links between different sets of Aria units. Dyna Accent Mini 
fixtures are shipped with the wireless system enabled (this does not prevent direct control 
via the cable) and the radio channel set to 0 as standard. For more details about choosing 
the most suitable radio channel, see page 19. 
Using an RDM (Remote Device Management) tool, you can quickly change between the 
various DMX personality modes. Various third party DMX/RDM tools are available; we 
recommend the Acclaim Lighting XMT-350 for this task.

TO CONFIGURE WIRELESS DMX USING THE ACCLAIM LIGHTING XMT-350

1  Connect the XMT-350 to the DMX input line of either a single fixture or multiple fixtures in 

a pre-arranged daisy chain configuration.

2  Power on the fixture(s) and the XMT-350.
3  On the XMT-350, press the 

MODE

 button, then use the arrow buttons to highlight the 

RDM

 function and press the   button to select. The XMT-350 will search for RDM devices 

and after a short while the XMT-350 will display a list of all located fixtures. The fixture that 
is highlighted within the list should begin flashing its emitters to identify itself.

4  If necessary, use the up/down buttons to highlight an alternative fixture. 
5  Press the   button to view details for the chosen fixture and then use the down button 

to highlight the 

MODEL

 entry:

6  Press the    button to view the options:

Within this menu, you can change the radio address and also enable/disable the wireless 
receiver circuit. 

7  To  change the radio address:

 Use the up/down buttons to highlight the WIRELESS ADDR 

option and press the    button. Use the up/down buttons to select the required address 
(between 0 and 14) and press the    button. For more details about choosing the most 
suitable radio address, see page 19.

8  Press the   button to return to the previous screen.       

DYNA ACCENT MINI

MODEL:

DYNA ACCENT MINI

MAN:

DMX START ADDRESS:

DMX SLOTS:

ACCLAIM LIGHTING

001

4

LABEL:

DYNA ACCENT MINI

DMX PERSONALITY: MODE1: 4CH-...

DYNA ACCENT MINI

0

WIRELESS ON/OFF

ON

WIRELESS ADDR

Summary of Contents for Dyna Accent Mini



























Reviews: