background image

2

www.acclaimlighting.com

INTRODUCTION

WELCOME

Welcome to the Dyna Accent Mini range from Acclaim Lighting. These compact rugged 
LED-powered fixtures are designed to replace traditional external spot/flood lights while 
using a fraction of the power. Featuring a die-cast aluminum body throughout with full IP66  
environmental rating, these fixtures are built to last. A choice of standard gray, black or white 
finishes plus special-order custom colors are available.
The Dyna Accent Mini range consists of two main variants:

 

Fixed white - 2700K, 3000K, 3500K or 4000K emitters, or

 

RGBW - Red, green, blue and warm white (3000K) LED emitters.

External control using the industry standard DMX-512A is supported via either cable or the 
in-built Aria™ wireless receiver. The industry standard RDM 

(Remote Device Management)

 

format is used for configuration. Dyna Accent Mini can be mounted in a variety of ways 
using optional mounting kits. 
The internal auto-sensing power supply can accept mains inputs between 100 to 240VAC at 
50 or 60Hz. Total power consumption is just 13W. 
Optional spread lenses and snoots are available. 

SAFETY

 

When fixtures are mounted off-ground, ensure that they are securely fitted to an 
appropriate mounting surface.  

 

Ensure that the power input is supplied from a correctly fused, earthed and 
environmentally protected location.

Summary of Contents for Dyna Accent Mini



























Reviews: