Lanier R/C
Sukhoi SU 31M
Instructions
F5 (1)
1/8” laser cut lite ply
F6 (1)
1/8” laser cut lite ply
F6A (1)
1/8” laser cut lite ply
F7 (1)
1/4” laser cut lite ply
Tank Mount 1/8" laser cut ply
FD (4) servo mount doublers 1/8” laser cut
lite ply
H1 (1) Hatch formers 1/4” laser cut lite ply
H2 (1)
1/8” laser cut lite ply
H3 (1)
1/8” laser cut lite ply
CR (1) cockpit rear former 1/8” laser cut lite
ply
HR1 (4) hatch retainers ¼” laser cut lite ply
HR2 (4) hatch retainers ¼” laser cut lite ply
HR3 (4) hatch retainers ¼” laser cut lite ply
Hatch floor
1/8” cnc router cut
TD1 (1) Turtledeck formers 1/8” laser cut
lite ply
TD2 (1)
1/8” laser cut lite ply
TD3 (1)
1/8” laser cut lite ply
TD4 (1)
1/8” laser cut lite ply
TD5 (1)
1/8” laser cut lite ply
TD5A
1/8” laser cut balsa
Firewall
½”x5.687”x7.110”
LG (Landing gear plate) 1/4” laser cut lite ply
TW (tail wheel plate) 1/4” laser cut lite ply
SI (4) stab incidence tabs ¼” laser cut lite
ply
W7 (4) wing incidence tabs
¼” laser cut
lite ply
TF (fuselage fairing)
1/32” laser cut ply
Instrument panel
1/16” laser cut ply
1”x1”x3/4”
ply tail wheel support
½”x1/8”x12”
tail wheel fairing
½”x3/4”x12”
tail wheel fairing
3/8”x3/8”x36”
tail wheel steering
mount, motor box top rails
½” tri stock x 36” (2)
F1 and motor box
reinforcement
¼”x7.58”x8.5” (2) motor box top and bottom
¼”x1/4”x48” spruce(4)
fuse side rails
¼”x1/4”x36 spruce (5)
fuse bottom
outside stringers
¼”x1/4”x36” balsa (24)
turtledeck, hatch,
and bottom stringers
3/32”x3”x36” (10)
balsa sheeting,
turtledeck and hatch
1-1/2”x18” phenolic tube
spar carry through
1/8"x12"dowel Pins for firewall
Clear instrument gauges
Printed instruments
Clear canopy
Aluminum landing gear (1)
Aluminum angles 1-1/2"x1-1/2"x3" (2)
Cowl
Fiberglass cowl top
Fiberglass cowl bottom
C1A (1) cowl top mount ¼” laser cut lite ply
C1B (1) cowl bottom mount ¼” laser cut lite
ply
Fin
Foam fin blank
FT (fin top, rudder inset) (2)
3/32” laser
cut balsa
1/16”x4”x24” (6)
sheeting
1/16”x4”x18” (4)
sheeting
1”x1-1/2”x11” (1)
fin tip
1”x2-3/4”x14” (1)
rudder bottom
3/4”x2-3/4”x14” (1)
fin trailing edge
1/2”x2-3/4”x14” (1) rudder leading edge
1/4”x1/2”x24” (1)
fin, rudder tip,
leading edge
1/2” dowel x 6” (1)
control horn hard
points
Stabilizer
Foam stab blanks (2)
S1 (2) tube reinforcement 1/8” laser cut lite
ply
ST (4) stab, elevator inset tips 3/32”x3”x36”
laser cut balsa
SR (2) stab root ribs 1/8” laser cut lite ply
ER (2) elevator end caps 3/32” laser cut
balsa
1”x1-1/2”x13-1/2” (2)
Balsa tips
1/16”x4”x24” (18)
sheeting
1/2”x1-3/4”x18” (4)
stab trailing edge
1/2”x3/4”x24” (2)
stab leading edge
25
