background image

14 

������������ ���� ���������� ������������

ABS lifting station Sanimat

C�mm����������

m

  The safety hints in the previous sections must be observed!

Before commissioning the unit should be checked and a functional test carried out. Particular attention should 

be paid to the following:

Have the electrical connections been carried out in accordance with regulations?
Is the direction of rotation correct - even if run via an emergency generator?
Was the control line (plastic hose) laid in such a manner that it has a continuous rise?
Was the collection tank secured against floating?
Has venting been installed in accordance with the regulations?

ATTENTION 

Before commissioning the collection tank should be cleaned of any large particles 

and filled with water.  If the control line (plastic hose) was connected to the 

submerged tube with the tank already full, then the collection tank must be fully 

emptied once by activation of the selector switch “Hand”.  After commissioning the 

faecal lifting station is normally operated with the selector switch in position “Auto”.

M����������

c

  Before commencing any maintenance work the unit should be completely disconnected from the 

mains by a qualified person and care should be taken that it cannot be inadvertently switched back on.

m

  When carrying out any repair or maintenance work, the safety regulations covering work in enclosed 

areas of sewage installations as well as good general technical pratices should be followed.

NOTE 

The maintenance hints given here are not designed for “do-it-yourself” repairs as 

special technical knowledge is required.

NOTE 

A maintenance contract with our works service department will guarantee you the 

best technical service under all circumstances.

6.1 

C�mm�����y �� m���������� �f L�f����� S������� �� ����������� w��h EN 1056.

It is recommended that the lifting station be inspected monthly and its function checked.
In accordance with EN regulations, the lifting station should be maintained by a qualified person at the following 

intervals:

in commercial premises - every three months.
in apartment blocks - every six months.
in a single family home - once a year.

In addition we recommend that a maintenance contract be taken out with a qualified company.

-
-
-
-
-

-
-
-
-

Summary of Contents for Sanimat 1501S

















Reviews: