Abit SM5 User Manual Download

Page: 68 / 96

Appendix A

A-6

Watch the pin position and the
orientation

Connect connectors P8 and P9 or the power supply unit to the correct connectors on
the mainboard.

Pin number

Name of the signal or

signification

Pin number

Name of the signal or

signification

POWERGOOD

Ground

+5VDC

Ground

+12VDC

-5VDC

-12VDC

+5VDC

Ground

+5VDC

Ground

+5VDC

There is an orientation pin. Connect

your keyboard connector to connector on the mainboard.

Connect the six-threads PS/2 Mouse cable that

comes with the hardware to the connector on the mainboard. Install the bracket
located on the other end of the computer case. When you buy a Mouse, it has to be a
PS/2 Mouse for it to be connected to this port.

Attach the bracket of Parallel Port, Serial Port and PS2 Mouse on the
computer case.

There is a specific orientation.
Connect the three-threads

CPU Fan power cable to the Fan connector on the mainboard.

Connector

SM5 (JP9)

SM5-A(JP9)

Pin number

Name of the signal or signification

Ground

+12V

Ground

Installing Power input connector:

Installing Keyboard connector:

Installing PS2 Mouse:

Installing CPU Fan Power
connector:

Summary of Contents for SM5

































































































Search results

Summary of Contents for SM5

Reviews:

Related manuals for SM5

Brands by name

Popular brands

Abit SM5, User Manual

Search results

Summary of Contents for SM5

Reviews:

Related manuals for SM5

Brands by name

Popular brands