Abit SM5 User Manual Download

Page: 4 / 96

1-2

Chapter 1

SM5/SM5-A

Specifications:

1. CPU frequency and voltage setup with

CPU “SOFT MENU™ ”

Setup of the mainboard’s frequency and voltage without DIP Switches or
Jumpers.

Modification of CPU operating voltage and frequency through software
configuration.

Modification of CPU operating voltage and frequency directly on screen.

2. Uses ZIF CPU Socket 7 for easy CPU installation

Three voltage regulator/cooling plate sets

for a more stable CPU

operating environment

Supports Intel Pentium

CPUs: 75MHz to 200MHz and P55C CPUs

with MMX

Supports all AMD sixth generation AMD-K5™ CPUs: 75MHz to
166MHz, AMD-K6™ CPUs: 200MHz and 233MHz

Supports all Cyrix sixth generation 6x86™ CPUs: P120+, P133+,
P150+, P166+

Reserved circuitry supports future sixth generation CPUs

3. Chipset

Intel 430VX chipset

Supports standard version PCI 2.1

4. L2 Cache Memory

256K or 512K of cache memory (Pipeline Burst SRAM)

Cache memory upgrade to 512K (the SM5-A do not support this
feature)

5. System DRAM

Four

72-pin

SIMM

sockets: support FP and EDO DRAM

Two

168-pin

DIMM

sockets: support FP, EDO and Synchronous

DRAM (SDRAM) (the SM5-A do not support this feature)

DIMM sockets use PC modules (3.3V Unbuffered DRAM) (the
SM5-A do not support this feature)

Up to 128MB memory configuration possible

Summary of Contents for SM5

































































































Search results

Summary of Contents for SM5

Reviews:

Related manuals for SM5

Brands by name

Popular brands

Abit SM5, User Manual

Search results

Summary of Contents for SM5

Reviews:

Related manuals for SM5

Brands by name

Popular brands